爱词霸英语   汉语   手机版   软件版下载 | English
每日一句:正在加载...
1.There is a concave rose garden of ground down inside his courtyard.
在他庭院里,有一片地面玫瑰花园。收藏指正
2.A gutter under the eaves of a roof.
水槽屋檐槽:收藏指正
3.The results of the water-surrounding rubbing wear experiments on the ZrO2 ceramics with various molding press indicate that the compact with a molding press of 150 MPa possesses a low wear rate and a favorable abrasive wear resistance.
对不同成型压力条件ZrO_2 陶瓷进行了水环境摩擦磨损试验,结果表明本试验条件ZrO_2 陶瓷磨损机理为沙粒冲击形成裂纹经扩展形成坑,使试样受到磨损,150MPa 压力ZrO_2 陶瓷具有较低磨损率,抗摩擦磨损能力好。收藏指正
4.To supply(a ceiling, for example) with decorative sunken panels.
用饰板装饰提供(例如给天花板)装饰镶板收藏指正
5.Result:No significant difference was found in proliferation index,apoptosis index and PCNA/PARP ratio of chondrocytes and histological grades of cartilage in the inferior facet processes between convex and concave side in AIS(P>0.05).
采用PCNA/PARP比值及组织学分级作为软骨内成骨活跃程度指标,并对其进行比较。 结果:AIS患者上、端椎和顶椎凸、关节突软骨组织学分级、软骨细胞增殖指数(PCNA)、凋亡指数(PARP)和PCNA/PARP比值比较均没有统计学差异(P>0.05)。收藏指正
6.The mean age was 13.5 years old. The histological grades were defined under the light microscope. The proliferation index(proliferation cell nuclear antigen,PCNA-index),apoptosis index(Poly ADP-ribose polymerase,PARP-index),PCNA/PARP ratio of chondrocytes and histological grades of cartilage in the inferior facet processes by immunohistochemistry were compared between the convex side and the concave side in AIS.
方法:16例AIS患者,平均年龄13.5岁,取上、端椎和顶椎凸、关节突进行组织学观察及免疫组织化学测定其软骨细胞增殖指数(proliferation cell nuclear antigen,PCNA)和凋亡指数(Poly ADP-ribose polymerase,PARP)。收藏指正
7.The figure of the moon as it appears in its first or last quarter, with concave and convex edges terminating in points.
蛾眉月月亮在上弦时或弦时形状,其边和边均汇合成点收藏指正
8.With the help of the 3D software ANSYS, the optimal design for spatial slope shape in Jinduicheng deep furrow pit was calculated.
采用三维有限元数值模拟软件ANSYS完成了金堆城深露天矿边坡空间形状优化设计,获得了适合于小北露天步深开采最佳采场方位及最优边坡形状。收藏指正
9.It is pointed out that length of flown-in material (LFM), which flows into female die from underside of blank-holder during forming, is an external index of local forming resistance.
提出将流入量(从压料面进入模型腔局部材料线素长度)作为衡量局部成形阻力指标。收藏指正
10.For different contact loads and roll to slide ratios,the influence of the indented surface on the oil filmpressure distrbution and film profile during the dent trav elling through the lubricated contact region is studied.
研究了表面坑在不同接触载荷和滚滑率情况,通过弹流润滑区时对油膜压力和形状产生干扰现象。 根据对微弹流润滑特征分析发现,只有在表面存在相对滑动条件,进入弹流接触区表面坑才随接触载荷增加被逐渐地压平变浅;收藏指正
尝试查询