爱词霸英语   汉语   手机版   软件版下载 | English
每日一句:正在加载...
1.The snow began to melt when the sun came out .
太阳出来时，雪开始融化。收藏指正
2.To melt(lard, for example) to separate out impurities; render.
提炼焙化（如，猪油）以分离出油渣；炼油收藏指正
3.melt (fat, lard, etc.) in order to separate out impurities.
为了分离出杂质而溶化（脂肪，猪油等）。收藏指正
4.Synopsis: This paper present the results of primary experiment on making ductile cast iron rollers directly with blast furnace melt, It is pointed out that with proper technologies by adding moltem Cr-Fe alloy into the molten blast furnace metal and controlling the level of Cr/Si, it is possible to make ductile cast iron rollers directly with blast fur- nace melt.
本文总结了直接利用高炉铁水浇注球墨铸铁轧辊的初步试验工作,通过分析模拟试验及实体浇注结果,指出,在适当的工艺条件下,向铁水中兑入Cr—Fe合金液,并控制铁水的Cr/Si比,可利用高炉铁水直接生产球墨铸铁轧辊。收藏指正
5.Our country import pitch rational advanced, transport choice, serve expressway construction of our country, Other chemical product in bulk to melt to transport and probe out a road to succeed for our country even on the other hand, Play the exemplary role, therefore produce the enormous economic benefits and social benefit.
我国进口沥青合理、先进、运输方式的选择，一方面是为我国高速公路建设服务的，另一方面也为我国其它化工品的散装化运输探索出一条成功的道路，起到示范作用，由此产生巨大的经济效益和社会效益。收藏指正
6.However, some analysts say this lead could melt away if the CORBA compliant object technology vendors cannot work out lower-level interoperability for their software.
然而，有些分析师认为，如果符合CORBA的对象技术供应商不能为其软件制订出低级的互用性（标准），已有的领先地位可能会丧失。收藏指正
7.To analyze the influence of melt transferring condition on direct spinning FDY full package ratio. Try to find out the best process condition of melt transferring. It is regarded that polycondensation load are controlled at 150～{200 t/d},melt flow is kept above 1.45 t/h,temperature of melt is 286 ℃,temperature of Dowtherm is controlled at 280～300 ℃,and transferring press is 21 MPa.
分析熔体输送条件对直纺FDY断头的影响 ,找出熔体输送的最佳工艺条件 ,认为缩聚负荷控制在 15 0～ 2 0 0t/d ,熔体流量保持在 1 45t/h以上 ,熔体温度在 2 86℃左右 ,保温道生温度在 2 80～ 3 0 0℃ ,输送压力在 2 1MPa时 ,可提高FDY满卷率收藏指正
8.The thixotropic experiments were carried out for a LDPE (PE-FSB-23D022/Q200) melt. The results show that the LDPE melt has complex time-dependent viscoelastic properties.
进行了一种低密度聚乙烯 (LDPE ,PE FSB 2 3D0 2 2 Q2 0 0 )熔体的触变环实验 ,实验结果表明该LDPE的粘弹力学特性具有复杂的非线性依时特性 ;收藏指正
9.To improve the filling velocity of aluminum melt of LFC process and decrease the pinholes,low permeability thermal insulation coatings should be applied. The results also point out that coating thickness can not be too larger,and 0.2～0.3 mm is proposed.
为提高消失模铸造铝液的充型速度，并减少其针孔，应采用低透气性的保温涂料，且涂层厚度不能太大，以0．2～0．3 m m 为佳。收藏指正
10.Scratch this kind of secretion from tree, unfreeze it by warm water, refine out wax, melt it again and filtrate and bleach if necessary.
将这种分泌物从树上刮下来后，用热水溶化，撇出蜡，再熔化后并过滤以进行精制，必要时再进行漂白。收藏指正
尝试查询
同义词辨析
这些动词均含“融化，溶解”之意。
melt : 最常用词，指任何固体的熔化过程，常引申作“消散、淡化或消失”解。
dissolve: 多指固体溶于溶剂的过程。
fuse: 可与melt换用，但侧重指在高温下使两种或两种以上金属的熔合，也可作引申用。
汉英释义