爱词霸英语   汉语   手机版   软件版下载 | English
每日一句:正在加载...
1.The researches represented that the main control factors affecting the quality of IED have: 1)the pressure of pressing powder;
研究表明除与正确的设计、所用材料的质量等因素有关外,影响火工品压药质量的主要控制因素有:1)压药压力值;收藏指正
2.The results show that as the sintering goes on,the density of the pressing mixed powder blank increases and is stabilized at 7.96g/cm3after sintering at 950℃for 4 hours,which increases by 4.3% com-pared with unsintered blank at the same time,and internal oxidation of Cu-Al alloy particles ocnurs.
结果表明,混合粉末压制成形后的压坯密度随烧结时间延长而增加,经950℃烧结8 h后稳定在7.96 g/cm3左右,较烧结前密度增幅达4.3%;收藏指正
3.Ti2AlC bulk material was synthesized by hot pressing using elemental powder mixture of Ti,Al and active carbon.
以Ti、Al元素粉和活性炭为原料,采用热压工艺合成了Ti2AlC块体材料。收藏指正
4.Fabrication of Ti_2 AlC material by in - situ hot pressing TiC/Ti/Al powder mixtures
原位热压TiC/Ti/Al合成Ti_2 AlC的研究收藏指正
5.Effect of Ni in α-Al_2O_3/Ni nanocomposite powders on the phase transformation temperature to alpha alumina pressing TiC/Ti/Al powder mixtures
Ni对纳米α-Al_2O_3/Ni粉体中α相转变温度的影响收藏指正
6.The preparation method and arc erosion characteristics of the AgNi and AgSnO2 contacts materials which was fabricated by high-energy ball milling, hot pressing and sintering were studed. The powder morphology and microstructure of contact were analyzed by X-ray Diffraction (XRD), Scan Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM).
利用高能球磨技术及热压烧结工艺制备出第二相弥散均匀分布于 Ag 基体中的纳米复合 AgNi 和 AgSnO2 触头,对复合粉末和合金触头进行了 X 射线衍射(XRD)、扫描电镜(SEM)和透射电镜(TEM)分析。收藏指正
7.Abstract: Factors that influence the delay precision of commerical delay detonator were introduced.The charging and pressing technique, variation and time variation law of the composition, the powder processing was discussed.
文摘:介绍了工业延期雷管延期精度的影响因素，并对装配工艺中的装压药工艺方法、药剂变化原因、药剂时间变化规律和制药工艺控制进行了讨论。收藏指正
8.MCR Magnetic Wedge of Iron Powder Type with Mould Pressing and Resistant to High Temperature for Motors
电动机 MCR 耐高温铁粉型模压磁性槽楔收藏指正
9.The machine is applicable to the plasticity material to inhibit the craft, such as hurtles to press, curve, turn over the side, lamella to pull to stretch etc. craft, also can used for correct, pressing to pack, the emery wheel model, the cold crowded metals spare parts model, the plastics product and the powder product of inhibit and model craft.
本机器适用于可塑性材料的压制工艺，如冲压、弯曲、翻边、薄板拉伸等工艺，也可用于校正、压装、砂轮成型，冷挤金属零件成型、塑料制品及粉末制品的压制成型工艺。收藏指正
10.The relationship between the anisotropic and magnetic properties of HDD Nd 14 Fe 73 Co 7B 6 powder and hot pressing techniques, heat treatment, have been studied in this thesis.
研究了热压工艺和热处理制度对成份为 Nd14 Fe73Co7B6合金的 HDD粉末各向异性和磁性能的影响 .收藏指正
尝试查询
汉英释义